In comparison, holding small nails between your fingers and then swinging a hammer at them, does carry a considerable risk. If you are screwing plasterboards, the risk that a screw, or the power tool is going to injure you is pretty small. Let’s face it, building sites, and even DIY jobs, can come with a risk of injury. As a result, this can have an effect on the fixings.
Hitting this with a hammer repeatedly, can cause a lot of movement. Often this is something like CLS, which is planed even further. Stud walls are most often made from a 3×2. For example, assume you are boarding some studwork. Someone with more experience is less likely to have this problem, but even skilled workers make the occasional mistake.Īs well as damage from miss hitting nails, you can also cause issues with the vibration and force that the hammer exerts. In a worst-case scenario, you could even put the hammer right through it. If you miss hit the nail you could easily dent the boards. Less chance of damaging boardsĪ hammer can cause a lot of damage to a plasterboard. If you use these on a ceiling, the nail heads are far more likely to pull through the plasterboard, causing it to come away from the joists. In order for the nail head to sit below the surface it usually breaks the paper entirely. In contrast, clout nails have a flat head. This means drywall screws cause minimal damage to the paper face. The underside shape of the screw allows it to depress the surface, pulling flush or slightly below.
The shape makes them ideal for soft materials, such as plasterboard. This is known as a bulge head, which is a type of countersink with a curved underside. The second advantage of a drywall screw is the type of screw head. This is less important on walls, but it’s definitely crucial for plasterboards fitted to ceilings. It also bites into the wood and gives a solid fixing, that is harder to pull out than a nail. This allows the screw to really pull the plasterboard tight to the timber. The first way they are superior is their coarse thread. Screws give better fixingsĭue to their design, screws give a better fixing in a couple of different ways. Obviously, if you have access to props, or even a board lift, this does change things slightly, but we can still go back to speed, where screws are far superior.
In contrast, this would be much easier with screws, or a screw gun. However, when it comes to boarding a ceiling, it is far more complicated when you are trying to nail.Įven fitting smaller boards it would be quite difficult for one person to fix to a ceiling with nails. If you are fixing plasterboards to stud work, then depending on experience, screwing is only slightly easier. We already discussed how easy it is to use a screw gun, but even a cordless drill is easier than hammering nails. You can see a great example of a good quality screw gun by clicking here Installing with screws is easier than nails As opposed to manually nailing 15-20 individual nails.Īlso, screw guns aren’t that expensive, especially if you’re doing a lot of boarding. This means fixing an entire board will take 1-2 minutes. All you need to do to fix them, is apply pressure and push the trigger.Īfter a small amount of practice, you should be fixing screws at the perfect depth, without any misfires or jams in the gun. The screws are loaded into the gun in a plastic strip. Using a screw gun is a game changer, it will allow you to fix boards extremely quickly, with very little hassle. However, even then, it is likely they can’t go as fast as someone experienced at fitting with screws.Īlso, if the person screwing is using collated screws and a screw gun, the person nailing has no chance.
Over the years, they have developed considerable skill and speed when it comes to nailing boards. You will still find older guys on site, who learnt to nail boards as an apprentice. Unless you are an older, more experienced plasterer, who learnt to fix plasterboard with nails, it is going to take you far longer nailing than screwing. 5 Reasons screws are better than nails for fitting plasterboardīelow you can see a few of the main reasons that drywall screws are a better option than clout nails: Screwing is faster However, in most cases, this is a false economy, as it will take you far longer than screwing. Another reason someone might choose nails, is because they are cheaper than screws.
0 kommentar(er)
